What happened to Spaform?

What happened to Spaform?

Spaform UK Ltd was in administration just before Christmas 2005, but has now been sold on to an Italian luxury bathroom company Teuco Guzzini for £4.5m.

What does Flo stand for on a hot tub?

an issue with water flow
FLO Error Message If your tub is displaying this message it simply means that there is an issue with water flow. This may occur for a number of reasons. On your spa’s heater, there are sensors that read water pressure or there may be a pressure switch. These determine the error.

How much is the Jacuzzi J 345?

$13,690
MSRP: $13,690. With room for up to seven adults, the J-345™ model offers ergonomically-designed seating and comes equipped with superior PowerPro® Jets, including bold FX Jets and a jetted foot dome to provide you with the finest hydromassage.

How do you program a Balboa hot tub?

To program, press “Temp,” then “Jets 1.” Press “Temp” to adjust. Press “Jets 1” to exit programming. For non-circ systems, low-speed pump 1 and the ozone generator (if installed) run during filtration. For 24 hour circulation systems, the circ pump and the ozone generator (if installed) run 24 hours.

How much does a Jacuzzi J 315 cost?

MSRP: $10,158. The compact J-315™ hot tub offers a combination of seating types. This model also offers high-performance hydrotherapy with mighty PowerPro® Jets to soothe and massage your muscles. The Jacuzzi® J-315™ Hot Tub model provides a private, intimate setting with enough room for 2-3 adults to relax comfortably …

How do you drain a Jacuzzi Premium hot tub?

To let the water out, you can drain the tub through the valve on the bottom of your spa. If your spa isn’t hooked up to a drainpipe, you can use a hose to drain the water. You can also use a submersible pump to speed up the process. Once drained, wipe your spa down and apply a non-foaming cleaner to the entire tub.

How long does it take for a Balboa hot tub to heat up?

It will take less time to heat if it is warmer outside. If you want your hot tub to be 100 degrees, it will take 4 hours to reach it’s temperature. If you keep your hot tub cover on, you can shorten that time.

How do you bypass a flow sensor?

How to Bypass a Flow Sensor in a Pool Heater

1. Shut off the circuit breaker that controls electricity to the pool heater and the pool pump that sends water through the heater.
2. Use a screwdriver to take out the screws holding the housing over the heater.
3. Detach the two wires from the sensor.

How do you reset the pressure switch on a hot tub?

Some adjustable pressure switches have an Adjustment Screw of grey plastic that accepts a small skinny flathead. Turn the screw slowly to the left, counter-clockwise, to reduce the minimum required pressure. Turn it slowly just barely beyond the point where the heater turns On.

What does F2 on my hot tub mean?

The F2 error code is usually from a balboa power pack system and normally is referring to a flow issue in your hot tub. There are a few things you can look for when trouble shooting an F2 error code on your hot tub. First it is always a good idea to cut the power to the unit and let it cool down and then reset it.

How many gallons does a Jacuzzi J-315 hold?

The J-315 holds 210 gallons of water and is just the right size for our 10-foot by 16-foot screened porch. Lounge seat (upper) showing 2 large jets and 4 small jets.

How many gallons does a jacuzzi 315 hold?

PowerPro FX Rotational Jets (2)

How often should you change hot tub water not?

With average use, your hot tub should be drained and refilled about once every three or four months.

How often does hot tub water need to be changed?

every 3 to 4 months
We recommend customers to change their hot tub water every 3 to 4 months. The reason we recommend this is that as your continue to add more chlorine, it will start to dissolve slower and slower until the chlorine doesn’t dissolve in your hot tub anymore.